Prototype PUF sandwich panels · The illustrated story

Two panels. Same batch. One is hiding something.

They come off the same line minutes apart and look identical. One has an air pocket inside its foam. Follow both from the chemical drum to the cold room, and see where a thermal camera on the line changes the ending.

Want the engineering detail? Read the full case study

Illustration of a continuous PUF panel line: steel coils, foam pour, double-belt press, saw, a thermal camera on a gantry and a stack of finished panels.

Hi, I'm Kelvin, the line's thermal camera. I look at every panel while it's still warm.

  1. Made the same
  2. The secret
  3. Two roads
  4. Where they end up
  5. What people get
  6. What it's worth
  7. How it's measured
  8. Behind the pictures
01 · Made the same

Same drums, same coils, same press.

A PUF panel is foam poured between two steel skins. The foam is two liquids, polyol and isocyanate, plus a blowing agent that puffs it up. The skins unroll from two steel coils. Both of our panels were made from exactly these.

Every lot is lab-tested before it's allowed near the line.

  • PolyolPart A of the foam
  • IsocyanatePart B of the foam
  • Blowing agentPuffs the foam up
  • Painted coilThe top skin
  • Galvanised coilThe bottom skin

Gate 1: every lot tested

  • Top skin profiled steel
  • Core PUF foam
  • Bottom skin steel

Then one line puts them together

  1. Steel coils
  2. Foam pour
  3. Double-belt press
  4. Saw
  5. Thermal camera
  6. Stack

Mixed warmBoth liquids are kept at their set temperature. Too cold, and the foam doesn't reach every corner.

Pressed at 40 to 45 °CThe foam rises and sets between two moving belts, gluing itself to both skins.

Cut to lengthA few minutes from pour to saw. Then the panel is stacked, wrapped and sent out.

02 · The secret

One of them has a pocket of air where foam should be.

For twenty minutes the isocyanate ran a few degrees cold. Cold foam doesn't fill the corners, so it left an air pocket just under the skin. From outside the panel is perfect. A tap test on one panel in twenty would almost certainly miss it.

Setting foam is warm. An air pocket isn't, so I see it as a cold patch.

Illustration: a sandwich panel sawn through, showing a hidden air pocket in the foam just under a perfect-looking steel skin.
Cut open, the pocket sits just under the skin. Nobody would see it from outside.
Illustration: a freshly made panel on the conveyor, looking normal. The same panel through a thermal camera: warm all over except one cold patch.
Drag across the panel. Left of the line is what the thermal camera sees a few minutes after the press.

AI-drawn illustrations, not photos or real thermal images from a plant.

03 · Two roads

What happens next depends on who sees it first.

Same panel, same pocket. Pick an ending.

  1. Illustration: panels leaving the factory on a truck.

    It leaves the plant

    It looks just like every other panel on the truck.

    Cost so far: nothing
  2. Illustration: on site, one panel in the wall has bowed and its joint won't close.

    It bows on site

    The skin lifts over the pocket and the joint won't close. A crew pulls it out again.

    A panel, a truck and a crew
  3. Illustration: a potato cold store with ice building on one wall panel.

    Or it ices up later

    If nobody spots it on site, warm air leaks in and freezes inside the wall. The potatoes beside it go bad first.

    Power, produce and repairs
  4. Illustration: the panel maker's owner taking an angry phone call.

    The phone call

    Nobody can say which batch it came from, so now the client checks every load.

    A client's trust

One hidden pocket, found weeks later and miles away, by the person who paid for it.

04 · Where they end up

Every room asks something different of the same panel.

Tap the dots to see what a hidden fault does in each room.

Realistic cutaway illustration of a pharmaceutical filling room and airlock built from insulated panels.

Pharma sterile filling suite

  1. Walls and joints must seal, or the cleanest room can't hold its air pressure.
  2. A void behind the skin dents when a trolley hits it. Cracked coating gives microbes a place to hide.
  3. Auditors ask what's inside the walls and ceiling. A record per panel answers in minutes.

Rooms that hold pressure and pass particle tests first time.

Realistic cutaway illustration of a potato cold store built from insulated panels.

Farm cold store at 3 °C

  1. A joint that opens in the cold lets warm air in, and frost builds around it.
  2. Damp gets into a void and freezes. That wall insulates a little worse every year.
  3. Potatoes stacked against a warm patch sprout or rot first.

An even 3 °C wall to wall, and lower power bills.

Realistic cutaway illustration of a dairy cold room built from insulated panels.

Dairy cold room at 2 °C

  1. Damp air from wash-downs pushes into any void and freezes there.
  2. Ice on a ceiling joint melts during defrost and drips onto open product.
  3. The panel record shows which panels sit over the product zones, so the right ones get replaced.

Dry ceilings and clean food-safety audits.

Typical problems in each kind of room. Results depend on the site; a pilot measures panels at the plant.

05 · What people get

Not a dashboard nobody opens. A message, a record, a report.

Each output goes to the one person who acts on it, where they already are.

When I hold a panel, a person hears about it within two minutes.

Line 1 · QC

Panel 1,284 held. Cold patch about 40 × 25 cm, 30 cm from the joint edge.

2nd cold patch in 6 panels. Isocyanate at 19 °C, set point 22 °C, since 2:09 pm.

→ Check the iso heater.
→ Tap-test panels 1,280 to 1,285.

Tap test: voidFalse alarm
Shift supervisorOn their phone, within a minute of the panel leaving the press. The reply buttons teach the model what was real.
Panel recordPanel 1,286Line 1 · 13 Nov 2026 · 2:21 pm
Panel
PUF wall panel, 80 mm, 0.5 / 0.5 mm PPGI
Thermal
Even, no cold patch
Skin
No dents or scratches
Size
6,000 mm long, 80.4 mm thick
Foam batch
40 kg/m³ (lab test, batch 2611-07)

Thermal image and both faces attached

The buyer, on siteScan the QR on the panel label. Pharma and food clients get the same records as one batch file for their audit.

Shift B report13 Nov · 2 pm to 10 pm

Made
4122,470 m²
Held
97 real, 2 false
Alert
1:40median, min:sec

What caused the holds

  • Iso temperature drop, 2:09 to 2:31 pm5
  • Skin dents at the stacker2
  • False alarm (wet patch on film)2
Plant owner and QC headEvery morning on WhatsApp and email: what went wrong, when, and the cause behind most of it.

Sample outputs from the prototype, with made-up panel numbers.

06 · What it's worth

Put in your line's numbers. See the money.

Every number here is an assumption, filled with typical values. Change any of them. The sum is shown in full under the result, so you can check it.

Saved a month

₹4.4 lakh

About ₹53 lakh a year

Faulty panels a month
450 m²
That reach a site today
225 m²
Caught at the line instead
158 m²
Saved on each one
₹2,800 per m²

450 m² × 50% × 70% × ₹1,400 × (3 − 1)

Not counted: the bigger gain. Catching a drifting mix early means fewer bad panels get made at all.

07 · How it's measured

Six weeks, one line. Targets agreed before we start.

The pilot runs beside your current QC, not instead of it. Every hold gets a tap test or a cut sample, so the numbers are checked, not claimed.

  1. Week 1

    Sit on the line. Log faults the way your team finds them today. That's the baseline.

  2. Weeks 2 to 3

    Fit the cameras and sensors in a planned stop. Record every panel without flagging anything.

  3. Week 4

    Train on your panels. Tune it until false alarms are rare enough to trust.

  4. Weeks 5 to 6

    Run live, side by side with your QC. Count what each one caught.

MeasureTargetHow we check it
Hidden faults caught at the line70% or moreTap tests and cut samples on held panels and a random sample of passed ones
False holds3 or fewer a shiftHolds the tap test clears
Time from press to alertUnder 2 minutesTimestamps on every hold
Panels leaving with a recordEvery oneRecords against the dispatch list
Panels traced to lab-passed lotsEvery oneEach record links its chemical lots and coils to their test reports

Results: published on this page when the first pilot ends, whatever they are.

Behind the page

Every picture here was drawn by AI from a one-line brief.

No photo shoot, no illustrator, no stock photos. We wrote short briefs, an image model drew them, and code cut, layered and animated the results. The same method makes mascots, product mockups, concept art, explainer scenes and animation parts for any project.

  1. BriefA sentence or two per picture, leaving the model room to be creative.
  2. DrawChatGPT's image model, in one project, so the mascot and the style stay the same throughout.
  3. SaveEach picture downloaded at full size, with a see-through background where it's needed.
  4. CutA row of objects split into separate parts; an exploded panel split into layers.
  5. AnimateParts slide, stack and reveal in code as you scroll, so the page stays light and sharp.

Realistic technical renders

For the line, its machines, materials and rooms: things a plant owner or a pharma buyer should recognise at a glance. The line was drawn whole first, then machine by machine in the same chat, so the parts match and can be put back together in code.

Photo-real

For the hidden pocket: a believable panel, then the same picture as a thermal camera would see it, made as an edit of the first so the two line up.

2D editorial

For the story: a cast-and-props sheet first, then every scene drawn with the same people and things.

2D line icons

For the pilot plan: quiet icons that sit with the text.

A mascot

Kelvin is the one playful thread: designed once, then posed again in the same chat.

The first direction we dropped

Everything in soft clay 3D. Friendly, but too toy-like for plant owners and pharma buyers, so it stopped here.

The checkered backgrounds show which pictures came back see-through. Briefs are shown as written.

Run a panel or sheet line?

Send us a month of rejects and complaints. We'll put your numbers in the model above and tell you honestly if a pilot is worth it.

Talk to us about a pilot